How to Revive a Brown Arborvitae Help Your Tree Recover and Regain Its Green Foliage

How to Revive a Brown Arborvitae Help Your Tree Recover and Regain Its Green Foliage 3

A once-full, green arborvitae can look beyond saving after its foliage turns brown and begins to drop. But brown foliage doesn’t always mean the whole tree is dead. If some branches and roots are still alive, the right care may help the plant recover.

Before you reach for the saw, look for signs of life and try to identify what caused the browning. Winter sun, drought, excess moisture, and transplant shock can all stress an arborvitae. The best way to revive a brown arborvitae depends on the cause.

Why Is My Arborvitae Turning Brown?

Arborvitae can develop brown foliage for several reasons, and not all of them are caused by disease.

Winter burn is common in exposed locations. When the soil is frozen, roots can’t take up water effectively, even as sun and wind continue to dry the foliage. The result may be brown, scorched-looking growth, especially on the side facing prevailing winds or winter sun.

Drought stress can also cause an arborvitae to turn brown. The tree needs consistently moist—but not waterlogged — soil. In hot, dry weather, light sprinkling may not deliver enough water to the root zone. On the other hand, soil that stays soggy can deprive roots of oxygen and contribute to root rot.

Newly planted arborvitae may turn yellow or brown because of transplant shock, root damage, or a change in growing conditions. Some stress after planting is possible, but rapidly spreading browning and brittle branches deserve closer attention.

How to Tell Whether an Arborvitae Is Still Alive

A dry-looking branch doesn’t necessarily mean the whole tree is dead. Start by gently bending a few small branches. Living branches are usually flexible; dead ones tend to snap easily.

You can also use a clean knife or your fingernail to scratch a small patch of bark. Greenish, moist tissue beneath the bark is a sign that the branch is alive. Brown, dry tissue usually means that section has died. Check several areas, including branches closer to the trunk, since the outer foliage may be more badly damaged than the inner framework.

If the trunk has large areas of peeling bark and the wood beneath is dry, or you can’t find living tissue anywhere, recovery is less likely. But if some branches are still flexible and green beneath the bark, it may be worth giving the tree time and proper care.

Prune Dead Branches Carefully

Completely dead foliage and branches won’t turn green again, so remove them with clean, sharp pruning shears. Cut back gradually to living tissue, rather than making a drastic cut based only on the appearance of the outer foliage.

Avoid cutting deeply into bare, old wood. Arborvitae may not produce new growth from sections that no longer have green foliage, so hard pruning can leave permanent gaps. If a branch still has green foliage and remains flexible, it may be best to leave it while the tree recovers.

After pruning, gently remove loose dead foliage from the canopy. Wear gloves, and clear away the cuttings — especially if you suspect pests or disease.

Water Deeply, but Don’t Overwater

If your arborvitae is drying out, watering it every day may seem like the answer. But too much water can be just as harmful as too little. Check the soil before watering: it should be moist around the root zone, not constantly saturated.

During dry weather, water slowly and deeply so moisture reaches the roots. How often you need to water depends on rainfall, soil type, temperature, and the size of the tree. A quick sprinkle on the soil surface may not be enough.

 

A 2- to 3-inch layer of organic mulch can help the soil retain moisture, moderate soil temperature, and protect surface roots. Keep mulch a few inches away from the trunk to reduce the risk of excess moisture against the bark.

Also check the planting depth. The point where the trunk transitions to the roots — the root flare — should be at or near the soil surface, not buried beneath a deep layer of soil or mulch.

Should You Use Plant Growth Products?

Gardeners sometimes use products such as Epin-Extra or Zircon when plants are under stress. These products can’t bring dead wood back to life, and they’re not a substitute for proper watering, pruning, or addressing root problems. If you choose to use a product, follow its label directions exactly; the recommended dilution depends on the specific product and its formulation.

Apply sprays in calm, dry weather, away from intense midday sun, and avoid mixing products unless the labels specifically say they’re compatible. The most important steps are still to identify the cause of the browning, maintain appropriate soil moisture, and avoid further damage to the tree.

How Long Does It Take an Arborvitae to Recover?

Patience is essential. An arborvitae won’t grow back in a few days, and new growth may take weeks to appear. Look for fresh, light-green tips on surviving branches and gradual improvement in the canopy.

Recovery from drought stress or winter burn can take more than one growing season. The timeline depends on the tree’s age, the extent of the damage, root health, and weather conditions. While the tree is recovering, avoid frequent trimming, transplanting, or heavy fertilizer applications. Extra fertilizer won’t repair damaged roots and may add stress.

If browning continues to spread, or you notice webbing, a coating on the foliage, insects, dark spots, holes in the bark, or other unusual symptoms, the cause may be pests or disease rather than simple drought stress. Contact a local arborist or your county Extension office for help with diagnosis.

A brown arborvitae may still be salvageable. Remove only confirmed dead growth, water according to soil conditions, and give the tree time to respond. Have you ever helped a browning arborvitae recover?